Ghost Immobiliser Fitting
Secure your vehicle from key theft, cloning, and hacking by using the first aftermarket CAN-Immobiliser. With the added option to connect to an Ghost app and GPS tracking system that can send you alerts to call if your car is tampered with or stolen.
Installing an Ghost immobiliser is a breeze for the qualified technician. The right tools, insulation tape, and heat shrink tubing is essential.
Getting Started
In contrast to physical security devices like wheel locks or car alarms, ghost immobilisers guard your vehicle without the need of key fobs or LED indicators. Instead, they connect directly to the ECU's CAN network and can only be activated after entering a PIN sequence. This gives a greater level of protection against key hacking, ECU swapping and cloning.
As a result, installing a ghost immobiliser Birmingham has to be done with great agility and precision. It's like navigating the minefield. A single mistake can cause serious damage to the circuits of the electrical system of your vehicle. It is essential to comprehend the installation procedure and prepare your vehicle properly.
First, you must prepare the vehicle by removing the interior panels to make space for the immobiliser unit. Once you've found the perfect place to hide it, use cable ties to secure it. Then, clean up the wiring by tying loose wires, and then using insulation tape or heat shrink tubing to cover exposed connections. This will reduce the risk of short circuits that are not intended to be there as well as improving the appearance and reducing the chance of tampering from thieves.
Then, locate a source of constant 12V power and an earthing point for the ghost immobiliser. Once you've identified these and tested the power wires with a multimeter to make sure they are delivering a consistent voltage. Then, connect the CAN H and CAN L wires from the immobiliser to the identified power source and the grounding point.
After you've made all the connections required It's crucial to double-check the connections and examine the immobiliser for signs of corrosion or other damage. By entering a PIN and then starting the car is a great method of testing the system. This should become a part of your routine, as it will allow you to spot any intermittent problems early. Regular testing will also help to prolong the life of the device, and keep it running at its peak performance.
Preparing your vehicle
The installation of the Ghost immobiliser is a complicated job that requires the appropriate tools and understanding. A wiring diagram of the vehicle is essential for locating the correct wires and making precise connections, while a multimeter is a great tool to check electrical values and ensure security. Cable ties and insulation tape can be used to guard connections from being tampered with and keep them secured. A user's guide will provide specific directions tailored to your Ghost Immobiliser model.
Once installed, a ghost immobiliser is able to stop unauthorised engine starts by requiring that the owner enter a unique PIN sequence by pressing buttons on the steering wheel or center console. The code can be altered at any time by the owner either by hand or remotely via a mobile app. The device also functions quietly and is undetectable to thieves as it does not emit radio frequencies.
A ghost immobiliser is connected to the CAN bus of the vehicle, a network that communicates with the electronic control units (ECUs) of the vehicle. It intercepts the signals sent by ECUs and then blocks the engine if a false signal is detected. The system is tamperproof and weatherproof, and does not include key fobs or LED indicators to attract the attention of thieves.
It can be placed behind or in a more obscure area to ensure that it isn't visible to thieves, and does not interfere with vehicle performance. It could even be placed in a small box and makes it less likely to be found during the test drive by unscrupulous salespeople selling cars.
Its stealthy operation, combined with its integration into the vehicle's CAN-bus system makes it an effective deterrent to vehicle theft techniques such as signal relay attacks and key copying. Combining the system with other security measures will create a formidable barrier that will deter even the most persistent of thieves. This is the reason why more insurance companies are recommending or even requiring ghost immobilisers to be installed, since it will significantly lower monthly premiums.
Making Connections
Contrary to traditional security systems which are heard by thieves ghost immobilisers operate in a quiet manner to stop them from knowing that your vehicle has been turned on. They also block high-tech methods of stealing vehicles, such as OBD hacking. They can also be fitted without causing permanent damage to your car making them a good option for those planning to sell their vehicle in the near future.
The Autowatch Ghost 2 is a immobiliser CANbus that is among the most reliable and advanced solutions to prevent car theft. ghost car immobiliser blocks your engine through the CAN data network and generates a unique PIN code which is difficult to steal from criminals to guess. It can be used on a wide range of vehicles, and works with a variety of features already installed, such as car alarms and steering wheel locks. GPS trackers and door lock bypass.
If you opt to use an Ghost immobiliser for your vehicle, make sure to refer to the wiring diagram to identify the wires that connect. Double-check their locations to make sure they are accurate, and label them or tape them to help you remember them. You will also need to locate a source of constant power (12V) and a grounding point to the system. Once these are in place, you can start to connect the components to complete the installation.
If the ghost immobiliser has been connected to your CAN bus, it will block your vehicle from starting until you enter a pin code through the buttons on the steering wheel or dashboard. This will stop ECU hacking keys cloning, hacking, and other techniques of theft from vehicles. It can also be paired with other Thatcham approved security equipment like alarms or tyre clips to give your vehicle an even greater degree of security.
As the UK automotive industry continues to grow and so do the options to secure your car. With so many ways for thieves to get in and steal your car it's crucial to do all you can to ensure it isn't taken away. Ghost immobilisers have become a popular option among car owners who are accountable.
Testing the System
The Ghost Immobiliser uses a CAN data network to communicate with the vehicle's ECU and prevent the engine from running until a specific PIN code is entered. This makes it extremely difficult for thieves to steal your key fob and start your vehicle, and more difficult to disable the system through hacking into its electronics.
Ghost Immobilisers are also able to be utilized in conjunction with GPS tracking devices that can aid in tracking your vehicle and track it in the event of theft. This isn't an everyday feature in security products that are available from the market however it's an excellent method to enhance your security and provide peace of mind knowing that your vehicle is always secure.
In addition to providing increased security, in addition to providing enhanced security, the Ghost-II immobiliser also provides a comfortable user experience by removing the need for additional key fobs and devices. It comes with an easy and simple PIN code entry system that is seamlessly integrated into your daily routine. It also has convenience features and deactivation modes that let you to temporarily disable the immobiliser so that you can park or service your vehicle.
Before you begin the installation process, you should familiarise yourself with your vehicle's wiring and prepare the required tools. A basic set of hand tools will give you the flexibility to make precise connections, while a multimeter can help check electrical values. Insulation tape and heat-shrink tubing are essential to shield connections from short circuits. Cable ties can also be used to secure wiring. Lastly, it's important to be in a well-lit space and wear the appropriate safety equipment when working with tools and electrical components.
You should test the Ghost immobiliser once you have completed the installation to verify that it's working correctly. Try to start the vehicle without entering the PIN. If this doesn't work then you'll have to retest and inspect the connections more thoroughly.
Contrary to other security devices unlike other security systems, unlike other security systems, the Ghost Immobiliser is a covert device that cannot be detected by thieves and is much more effective than conventional physical deterrents like wheel clamps or steering locks. It is TASSA acknowledged and approved by some insurance companies, which makes it a cost-effective investment that will provide you with the peace of mind you need.